Installation Instructions and Tips

	Bus wire is heavy duty stranded copper.  Ribbed channels fit into the contoured bottom  of the lamp holder for perfect alignment.		Bus wire is marked with a scale for easy measuring.  Rubber cap insulates the wire end.
	MR16 Light swivels and rotates for perfect positioning.		MR16 pivot fixture snaps right into the festoon lamp holder to convert to MR16 bulbs.
	Metal prongs connect to bus wire when bus wire is sandwiched between the lamp holder top and bottom		Festoon bulb snaps into the lamp holder and then can be rotated in place, to  change the direction of the light beam
	Lamp holder with 44mm 9led festoon bulb and bottom snapped into place.  Bottom can be removed by pushing tabs with a small screw driver.   Lamp holder can be repositioned onto bus wire over and over again.		Lamp holder shown with track cover on right side and no track cover on the left side.
	Track can be screw mounted or stuck to any surface using two sided tape, or silicone glue/caulk.		Transformer is wired for standard 120 volt household current, and converts to 12 volts output, to power the bus wire and operate the low voltage lighting.

Installation Steps

Step 1	Cut Bus Wire to Length.
Step 2	Position and snap lamp holders onto bus wire sandwiching the bus wire between the top and bottom of the lamp holder.
Step 3	Snap lamp holders with bus wire into track.
Step 4	Cut Track covers to length and snap onto track in between lamp holders.
Step 5 (Festoon)	Install festoon bulbs.  Insert one side of bulb into the hole, so bulb is at a 45 degree angle, and then press the other side of the bulbs down. Remove bulbs using a small screw driver.  Pry outward on the metal tip of the bulb on one side.
Step 5 (MR16)	Snap MR16 pivot fixtures in to place.
Step 6 (MR16)	Install MR16 lights.

Tips

Note:  The individual wires on the transformer and bus wires must remain separated.  If the wires are shorted together, the lights will not work, and this can also be a fire hazard  Note: (if you do not understand this tip, you should not attempt to install this system yourself).  This system should be installed by an electrician if you do not understand basic wiring. 

• To insert the festoon bulbs, you must insert one end first.  Insert the bulb into the lamp holder so that the one tip of the festoon bulb fits into the small hole on one side of the lamp holder metal contact.  Press the other side of the festoon bulb downward until it snaps into the lamp holder.

• To remove a festoon bulb, use a small screw driver to remove the festoon bulbs by prying one end of the metal end cap upward.

• The lamp holders can be removed and repositioned as desired.  Use a small screw driver to depress the tabs on the bottom of the lamp holder to release the lamp holder from the bus wire.

• To adjust the MR16 bulbs, push on the pivot fixture, not on the bulbs.  Pushing on the bulbs will dislodge then from the fixtures.

• You can leave some space between adjacent sections of track.  Us the track covers to cover the gaps between track sections.

• Be sure to use the transformer reference table so you do not overload the transformer.

• Be sure the power is turned off before installing the light bulbs.  If leds are installed with the power on, they will not light until the power is switched off and then back on again.

• You must have at least 3-4 led festoon bulbs , or 2-3 MR16 bulbs connected to the transformer.  The transformer will not light the bulbs if there are not enough leds connected.

• The transformer can be connected to power using a plug, or wired directly. 

• Soldered connections are best, but quick splices can also be used to connect the wires.

• The individual wires on the transformer and bus wires must remain separated.  If the wires are shorted together, the lights will not work, and this can also be a fire hazard  Note: (if you do not understand this tip, you should not attempt to install this system yourself).  This system should be installed by an electrician if you do not understand basic wiring.

• The lights should be tested before the track section is mounted. This will allow you to modify things without having to remove the track sections.